Dolls acquiring a teenage women acquiring a large sweater plus a skateboarding teenage boy in shorts may be produced with miniature brooms. The broomstraws complete may be the dolls hair. Complete instructions receive.
(Note: Use thick craft glue helping you to connect felt and best skateboards construction paper pieces together. Use glue gun for other things Use photo becoming an setup guide. Squeeze bit of paint onto paper plate if needed. Let paint dry before proceeding to a new color.
For mind, use flat paintbrush to paint front and side edges of wooden spoon with flesh let dry. For each eye, dip handle finish of paintbrush into black paint touch brush handle to wide finish of spoon. Use liner brush and black paint to paint nose, mouth, and eyebrows. For cheekbones, mix neon pink with that makes it. neon pink paint cheekbones. Let dry.
To produce figure, see Fig. 1. Place broom, bristles up, on work surface. For arms, center and glue 7" duration of chenille stem to back of broom where broom bristles . Bend arms around each side of broom glue arms to sides of broom to secure.
For body, utilize a generous volume of glue helping you to connect body to front of broom handle, covering center of arms.
For legs, use sandpaper or file to slightly flatten one finish of each and every craft stick. Glue one craft stick, rounded complete, to left side of body on top of broom handle to make sure the the most effective leg is despite bottom of body. Making certain bottom of legs are, glue right leg to back of broom handle much the same.
For each skate, glue one oblong to bottom of each and every leg to make sure that flat a part of leg reaches one finish of skate and toes point forward. Paint legs and skates with black.
Cut sweater, headband, and boom box patterns from Pattern Section, cutting along dashed lines for boom box. Use sweater and headband patterns to reduce materials as indicated. Set boom box pattern aside.
Using sweater pattern just like a guide, use black marker to draw in wavy lines at finish of each and every sleeve and along hem line on sweater front and back. Place one sweater piece, right side lower, on work surface. Spread an sufficient volume of glue on back of broom handle center handle on sweater back and press in place. Position arms to make sure that exact arm is centered along duration of each sleeve glue arms to center of sleeves. Departing hem, neck, and bottom of sleeves open, glue outdoors edges of sweater front to sweater back.
For each hands, bend finish of each and every chenille arm upward use wire cutters to trim excess stem, departing singleOr4" extended hands extending beyond side of sleeve. Use neon pink to paint a wavy line across neckline also to paint three buttons, evenly spaced, lower center front of sweater.
For wheels, paint front, back, and edges of each and every wooden circle with neon pink. For wheel hub, use black to paint a u . s . states . states .in center of each and every wheel somewhere let dry. With wheel hubs out, vertically glue some wheels to bottom front of just one skate another volume of wheels to bottom back of skate. Repeat for second skate.
For hair, cut several bristles from back of mind. With bottom edges even, glue bristles vertically across top front of mind trim ends if needed. Glue headband within the the most effective mind to make sure topping side of headband is despite bottom of bristles. Use neon pink to paint a wavy horizontal line across top and bottom edges of headband.
For hair bows, cut neon eco-friendly ribbon into two 5" lengths. Gather somewhat bundle of bristles together at left side of hair. Wrap ribbon around bundle tie ribbon results in a 2-loop bow with 1/2" loops and 1/2" tails. Cut ribbon creates a slant. skateboarding tips and tricks and Repeat for opposite side of hair.
For boom box, use pattern to reduce two boom box pieces by using this. pink construction paper set one piece aside for back. For loudspeakers, use boom box pattern as useful method of trace one speaker onto tracing paper. Eliminate circle. Use speaker pattern to reduce two loudspeakers from black construction paper. Use thick craft glue helping you to connect loudspeakers, evenly spaced, across front of boom box. Using pattern just like a guide and black marker, draw buttons, tuner, and tape cassette onto boom box.
For necklace, string beads on remaining 10" duration of string or floss. Wrap necklace around neck and tie ends together within the overhand knot.
For mind and legs, paint front and side edges of spoon and front, back, and side edges of ordinary craft sticks with flesh let dry. For cheekbones, mix some neon, that makes it. neon orange paint cheekbones. For mouth, use black to paint a curved mouth centered below cheekbones.
Working much the same as Rosie: glue mind, arms, and legs to body for foot, glue one wooden oblong to bottom of each and every leg, except have both foot slightly pointing to left.
Cut shirt, shorts, shoe, skateboard, shades, and headband patterns from Pattern Section use patterns to reduce materials as indicated. Set skateboard pattern aside. Much the same as Rosie’s sweater, glue shorts to bottom of body and shirt to top. Shape arms as preferred. Cut bristles from back of broom and canopy the very best mind much the same as Rosie. Glue headband within the the most effective mind. Glue shades below headband.
Use neon orange to paint the following: two diagonal stripes on right leg of shorts a horizontal wavy line across headband and dots on shirt front. Let dry. Turn figure over. Use neon orange to paint dots on back of blouse let dry.
To paint footwear, use pattern just like a guide. To start with shoe, place two shoe pieces flat on work surface with toes together. Paint large circles and eyelets with neon pink. For shoelaces, use black to paint a vertical wavy line lower each side of shoe. Repeat for second shoe. Let dry. Helping you to connect footwear to foot, see Fig. 2. With colored sides facing out, place two shoe pieces together around bottom of leg. Glue shoe pieces together at front and back edges, departing top front of shoe slightly open.
For skateboard, place skateboard pattern on jumbo craft stay with rounded finish of pattern matching rounded finish of craft stick. Use pencil to draw in a line across craft stick at straight finish of pattern. Use saw or utility knife to reduce rounded finish from stick. Sand or file cut edge smooth.
Paint front, back, and sides of skateboard. Using pattern just like a guide, paint a eco-friendly, pink, and orange stripe diagonally across front and sides of board.
For wheels, paint wooden circles with black. For wheel hubs, paint circle in center of each and every wheel somewhere with neon orange. With wheel hubs out, vertically glue some wheels to bottom front of skateboard to make sure that wheels are 5/8", apart and front edges of wheels are 1/2" from rounded side of skateboard. Much the same, glue another volume of wheels to back of skateboard to make sure that back edges of wheels are 5/8" apart and " from back side of skateboard. Paint over any uncovered glue with appropriate shade of paint let dry. how to choose a good skateboard for beginners
With plenty of glue, center and glue figure to skateboard.